Graflex Side Lighting Unit #2712
Manufactured by Graflex Inc. 3" tall x 1-7/16 diameter. 2 extension slots.
Few light scratches, otherwise in very good clean condition.
This can also be used for 'Star Wars' Light saber construction.
$25.00
Graflex right angle light unit #2745 (2ea)
Manufactured by Graflex Inc., Rochester, NY
(this is for use with a Graflex Flash Graflite 2-cell Flash Unit model #2772)
. One unit metal socket is completely smooth round, while the other has the indentations as seen in picture; this is not a flaw, but rather how it was manufactured.
$10.00 ea
 |
 |
HEILAND HR Strobonar 3-cell flash handle with 6" reflector
-SOLD-
Handle part no. 62227 Cosmetic marks/scratches on the chrome handle/a couple of marks where chrome pitted. Paint chipped on reflector.
$35.00
 |
|
Graflex Graflite JR No. 2770 Synchronizer Battery Case
-SOLD-
2-cell handle. Plugins for Extension N, Extension BC, Shutter. Some scuffing on the body.
$20.00
 |
Flash handle extension tube
-SOLD-
Threaded on one side. 1'1" long x 1-3/16" inside diameter. Looks like anodized aluminum; cosmetic/scuff marks; some kind of left over dirt marks inside threaded side of handle
$5.00
 |
Graflex graflite flash body ,upper and lower mounting brackets/clamps
Clamps diameter 37mm. Upper clamps have release buttons; as you can see on the left picture, one of the clamps is missing the pin that goes inside the spring. Tab width inside 24/25mm. Bottom clamps tab inside 24/25mm; square bottom part total width 41mm. Great condition; few scratch/scuff marks on body.
(for vintage Graflex, Heiland, King Sol or other flashes)
$15.00 (per set)
 |
 |
Graflex Graflite Flash clamp-on bracket
16.5cm (6-1/2") total length; clamp: 8cm length x 4cm width(3-1/4" x 1-1/2"); metal clamp widest width 6cm (2-1/2"); flash/tripod mount screw looks like 6-7mm dia.,wide thread type; paint chipped right above bolt.
$25.00
Graflex Pistol Grip strobonar flash bracket with base
-SOLD-
Made in Germany
28cm (11") total length with grip; 17.5cm (6-1/2") length metal bracket without extension; metal extension part appx. 11cm (4-1/8"); inside rubber base portion:7.8cm (3-1/6") length x 6.6cm (2-5/8) width; total base:8.2cm x 7cm; base circle inside dia 39mm with wide threaded mount hole of 5mm. Base excellent; metal has scratches on it.
$45.00
 |
 |
 |
|
Top bracket for the pistol grip above 15.5cm high x 7.5cm width(6" x 3"); 4mm & 7mm threaded holes at top (I didn't undo the extension screw, but fits perfectly) |
|
 |
 |
Flash mounting ring to bracket
-SOLD-
Very nice condition. unamed. 38mm dia.; whole length 42mm; 2.5cm height
$5.00
Graflex SR battery booster Cat.No.2095
Made in the USA by Graflex, Inc. 117v, 0.5amp,60hz
$40.00
Lamp is lit when plugged in. The 33ft SR-20 extension cable has a 4-female post connection on one side, and 4-male pin connection on the other; cable is supple, but insulation cracking.
 |
 |
Info from the net:
"Graflex Model 2095 Booster that was used to boost (and extend the useful life) of the dry cell high voltage batteries that were used in the Graflex HV power packs (not the RG Ni-Cad battery packs) that powered the electronic flash lamp heads. "
Info from Google docs:
"The SR Battery
Booster was not a
charger, but a device to
help obtain the maxi-
mum energy from the
batteries. It actually
depolarized the batteries to bring them back to normal opera-
tion, keeping the recycling period to a minimum. If the Battery
Booster was used properly, it could double the number of
flashes received from the battery.b. The Stroboflash Units could be used with the Battery
Booster connected, using the 20-foot Extension Cord, while the
batteries were being used, minimizing battery drain.c. The Battery Booster could be used to re-form the Strobo-
flash Units' capacitors. Electrolytic capacitors could become
de-formed if a unit was idle for several months, minimizing
battery drain as well.The SR 20-foot Extension
Cord (catalog number 2050)
was very useful in a number
of ways:a. As mentioned earlier, it
was used with both the Bat-
tery Booster and the Battery
Analyzer.b. The Extension Cord could
provide multiple lamp operation using a second or even a third
lamphead from a single Power Pack for in-studio operation (I
would suggest a second lamphead for a Stroboflash II Power Pack
and a third, if necessary, for the Stroboflash III & IV.). This could
be accomplished in two ways: First, one or two extension cords
connected in parallel. Second, two or three extension cords in a Y
connection.c. By adding one or more extra lampheads, there was a slight loss
of light... three lampheads, approximately -stop of the total light
output. The light was divided as follows: 50% to the normal heads,
30% to the second lamphead, and 20% to the third lamphead. With
just two lampheads, it was 60% and 40% with no appreciable loss
of light."
Singer Graflex Globe Strobe 250 bare bulb flash
-SOLD-
made in Rochester, NY. Exposure Guide at 75 Watt sec.: ASA/Gn 64/33, 100/40, 160/52,400/80
$125.00
Here are some links I've found relating to the Globe Strobe 250:
http://photo.net/bboard/q-and-a-fetch-msg?topic_id=23&msg_id=0004iC
http://graflex.org/helpboard/viewtopic.php?t=4950
http://graflex.org/helpboard/viewtopic.php?t=3006&sid=a32a41168818bb6526369a5d157e4162
I tried the handle, but it doesn't seem like it unscrews at the bottom, but at the top it is held by four screws. I unscrewed them and took pictures of the inside.
I loaded the pics here:
http://s1232.photobucket.com/albums/ff368/mindtab/globestrobe250/
The writing on the inside piece:
"GENERAL ELECTRIC 85F106AA RED710UF-450WDC 510VDC SURGE 1887218 MADE IN USA"
 |
